Thursday 10th May 2018
WHERE TO USE FLOORWASH
On what floor you can
use Floorwash?
All the floors are cleaned. Pottery, stoneware, clinker, terracotta, mosaic,
rubber, resin, marble, linoleum, raw concrete, gneiss, gneiss, stone, carpets,
rugs, mats, runners.
I have an outer
surface and porous, can I use Floorwash?
Sure that the bristles of the brushes 2 working in the opposite
direction from each other with a speed of 800 revolutions per minute can detach
the dirt in the pores and cracks and recovering tank immediately.
Can I use Floorwash
for carpets and rugs?
Due to the special brushes softer for fine rugs, vegetable fiber,
synthetic fiber and long-haired floorwash is perfect for washing carpets and
rugs: respects the delicacy of the fabric, the brushes work in two ways
reviving the color, recovers dust, dirt and pet hair nested deep, ensuring
hygiene and cleanliness unsurpassed. It is not necessary to move the carpet:
with the water recovery, floorwash leave clean and dry in minutes, without the
need to take him out to dry or drip!
You can switch the
wax on the floors?
Sure! The Floorwash is ideal to remove old wax from your floors.
Floorwash removes and recovers completely the old wax: for best results, you
can use the special cleaner wax remover.
Can I use Floorwash
in a work environment very dirty?
Obviously you. The quality of the cleaning system Floorwash is specific
on different surfaces but with an absolute right, that the removal of dirt
through a mechanical action. And 'particularly suitable model for M30 offices,
garages, retail space, warehouses or industrial areas.
What kind of dirt can
be removed with Floorwash?
Compared to traditional suction machines the innovative mechanical Floorwash
collection system allows the collection of small solid parts (hair, butts,
leaves, paper) without the risk of clogging the filter. For this reason, the
performance of aspiration are exploitable always 100% of the potential.
IMPORTANT TIPS
For any maintenance ALWAYS disconnect the plug. Do not turn off the
machine NEVER pulling the power cord and do not put NEVER operate the machine
when the cable is damaged or the outer casing shows visible damage. BE SURE to
store the machine properly after use, so make sure the blades are not touching
the floor. NEVER storing the camera in humid or not sheltered from the weather.
AVOID using detergents foamy, acidic, basic or diluents generally. Before
operating the machine firmly attach the power cord into the joint located above
the reservoir (fig 17 user manual), so that it runs under the brushes during
cleaning: the damage can be severe. ABSOLUTELY not wash the machine after use
with water or steam jet.
END USE: Remove and empty the waste bath water, then
carefully wash it under running water and dry it before storing it in the
machine. Unhook the cover and wash it gently with running water, making sure to
dry it before you hang up the machine. Download or empty the tank from any
remaining water or detergent. After disconnecting the plug clean with a damp
cloth and wipe the camera body later.
WHAT IF .....
The machine does not
work?
Check that the plug is inserted correctly. Check that the power cord is
fully intact. Be sure to press the kick-starter before slowly lowering the
handle.
The tank washing
water loses?
Check that the water valve of the cable is fully screwed to the tank.
Check that the drive cable anchored to the lever of the liquid distribution
(Fig 10 user manual) is not too taut.
The machine does not
distribute well the wash water?
Make sure the holes distribution liquid placed under the cover are not
clogged, if not lift the lid and gently clean the holes distribution using a
mild acid and warm water. Check that the tube is crimped or broken.
The machine does not
collect water?
Check that the waste is properly inserted and that the cover is
completely closed and attached to the body. Check that the wash water drops on
a regular basis when you pull the lever. Check that the blade steel inserted in
the tank is not too worn. Check that the brushes are not too worn.
The machine leaves
streaks of dirt side on the floor?
Bring out the liquid too long taking pulled the lever of distribution,
in this regard, please note that the lever must be pulled into the stage of
advancement, and left during the return (excluding carpet cleaning).
The machine
"jumps"?
Check that the brushes are not too worn, dirty or dry. Check that the
bristles of the brushes are not bent, this problem occurs in the case of
prolonged stop of the machine without having brought the handle upright. If
after making these checks do not get positive results, immediately contact FCM
Srl that will be at your disposal with skilled technicians and the full range
of original pieces as manufacturer. In case of tampering with the machine or
attempt to repair it by unauthorized technicians, FCM Srl will be forced to
apply the warranty if not yet in force.
